А я то думал что плаги на борту идут и их можно на каналах использовать
впосле достойный аппарат за такие деньги .Владельцы есть ТУТАААААААААААААААААААААААААААААААААААААа :blink:
http://www.focusrite.com/product/saffire_pro_26_i_o/
<div class='quotetop'>Цитата</div>
Hello XXXXX,
Thanks for the message.
The Saffire plug-in suite is a VST / AU set of plug-ins that can be used in your DAW software. These plug-in can be loaded as many time as you like in your project, and are powered my your computers CPU, so that will be the limiting factor as to how many you can load.
These plug-in cannot be loaded into Saffire control, therefore cannot be inserted on the input channels. (The original Saffire has DSP effect that can be put on input channels, but this is the only one in the range that has this feature).
Let me know if you need more info,
best regards.
Oliver [/b]
<div align="center">SAFFIRE PRO 26 I/O
SYSTEM REQUIREMENTS, PERFORMANCE AND SPECIFICATION
Windows
Operating System
Windows® XP Service Pack 2 (Home, Professional, 64bit XP or Media Centre Edition) or Windows Vista (32bit and 64bit - all versions)
Computer
Windows® XP compatible PC
400MB/s IEEE1394/FireWire port (OHCI compliant recommended)
CPU/Clock
1.4 GHz Intel or compatible
2.0 GHz Pentium© 4 or Xeon recommended for 192kHz operation
Memory (RAM)
256MB or more
512MB or higher recommended
Apple Mac
Operating System
Mac OS X Panther (10.4 or later) - OS Version subject change
Computer
Apple Mac Power PC G4, G5 or Intel Mac (any)
CPU/Clock
G4/800 MHz (minimum)
G4/1.5GHZ or higher recommended for 192kHz operation
Memory (RAM)
256MB or more
512MB or higher recommended
Additional Info
Firewire chipsets from TI (Texas Instruments), VIA, and NEC are recommended
It is highly recommended that Saffire be run on its own Firewire bus/card
In order to use Saffire with a 4-pin IEEE 1394 port you will need a 4-pin to 6-pin cable (not included) and must use the PSU (included)
NOTE: Saffire PRO software allows input mixing at 44.1/48kHz and 88.2/96kHz(ADATS disabled). When ADATs are enabled, at 88.2/96kHz mode, the input mix functionality is no longer available. The input mix is unavailable at 192kHz.
Microphone Inputs
Frequency Response: 20Hz - 20kHz +/- 0.1 dB
THD+N: 0.001% (measured at 1kHz with a 20Hz/22kHz bandpass filter)
Noise: EIN > 120dB (measured at 60dB of gain with 150 Ohm termination (20Hz/22kHz bandpass filter)
Line Inputs
Frequency Response: 20Hz - 20kHz +/- 0.1dB
THD+N: <0.001% (measured with 0dBFS input and 22Hz/22kHz bandpass filter)
Noise: -90dBu (22Hz/22kHz bandpass filter)
Instrument Inputs
Frequency Response: 20Hz - 20kHz +/- 0.1dB
THD+N: 0.004% (measured with 0dBu input and 20Hz/22kHz bandpass filter)
Noise: -87dBu (20Hz/22kHz bandpass filter)
Weight and Dimensions
3kg - 35cm x 4.5cm x 23.5cm
Analogue Input Specs
Mic: 8 x XLR on rear panel
Mic Gain: +13dB to + 60dB
Line 1-8: 2 x 1/4” TRS Jack (front panel)
Line 1-8 Gain: -10dB to +36dB
Instrument: As above, switched to Instrument (inputs 1 & 2 only)
Instrument Gain: +13dB to +60dB
Analogue Output Specs
Line level 8 x 1/4” TRS Jack
Nominal output level 0dBFS = 16dBu, balanced, +22dBu globally switched with external PSU connected across all outputs
Frequency Response: 20Hz – 20kHz +/- 0.2dB
THD+N <0.0010% (-100dB) (measured with 0dBFS input 22Hz/22kHz bandpass filter, un-weighted)
Software switched hardware DIM –12dB in output pairs 1-2, 3-4, 5-6, 7-8
Software Digital Volume control for all outputs
All outputs are useable as monitoring outputs
DIGITAL I/O (Saffire PRO 26 i/o)
1 x SPDIF In / Out (RCA phono) on rear panel (24-bit, 192kHz) Output transformer isolated
2 x ADAT In / Out (44.1 / 48kHz), 16 channels
1 x ADAT In / Out (88.2 / 96kHz), 8 channels S-MUX
Word clock input on BNC
Word clock output on BNC
Clock Sources: Internal clock, Sync to word clock on S/PDIF, Sync to word clock on BNC word clock input, Sync to word clock on ADAT1 or ADAT2 inputs
A/D Dynamic Range 110dB 'A-weighted' (all inputs)
D/A Dynamic Range 110dB ‘A-weighted' (all outputs)
Clock Jitter < 250 pico seconds
Sample rate 44.1 to 192kHz
DIGITAL I/O (Saffire PRO 10 i/o)
1 x SPDIF In / Out (RCA phono) on rear panel (24-bit, 96kHz) Output transformer isolated
Clock Sources: Internal clock and sync to S/PDIF
A/D Dynamic Range 110dB 'A-weighted' (all inputs)
D/A Dynamic Range 110dB ‘A-weighted' (all outputs)
Clock Jitter < 250 pico seconds
Sample rate 44.1 to 96kHz
MIDI I/O
1 in / 1 out on rear panel
Firewire 400 (1394a)
2 ports
Power
Either via Firewire (1394a) or external PSU (included)
Headphone Monitoring
2 x 1/4” TRS Jack on front panel (mirrors outputs 5-6 and 7-8)
High power headphone drivers
</div>
